Please view the following video for recommended installation instructions or view the step-by-step instructions. 


The default PIN for Navistream cameras is 3333.

 


Step 1: Prepare for Power Connection 

This step focuses on safely connecting the dashcam's power source to the vehicle's fuse box.

  • Locate the Fuse Box: Consult your vehicle's owner's manual to locate the main fuse box which is often under the dash or by the drivers kick panel. 

  • Prepare Tools: Have a circuit tester/multimeter, standard needle-nose pliers, wire crimpers, and appropriate hand tools ready.

  • Identify a Constant Power Fuse:

    • Ensure the vehicle's ignition is OFF.

    • Remove the plastic panel covering the fuse box.

    • Using the circuit tester, carefully test the existing fuses to find one that has constant power (power even when the ignition is off).

    • Note: If possible, choose a fuse for a non-essential circuit with constant voltage and avoid all safety-critical systems like airbags or ABS.

  • Install the "Add-a-Circuit" Fuse Tap:

    • The "add-a-circuit" kit has two slots: Slot 1 for the existing fuse and Slot 2 for the new dashcam fuse.

      • Remove and place the existing fuse (the one you removed from the vehicle) into Slot 1.

      • Place the new fuse (for the dashcam, typically 2-5A) into Slot 2.

  • Connect the Power Wire:

    • Use the wire crimpers to firmly crimp the exposed wire from the dashcam hardwire kit to the spade connector of the "add-a-circuit" fuse tap.

    • Plug the completed "add-a-circuit" into the fuse slot you identified in the fuse box.

  • Connect the Ground Wire:

    • Locate an unpainted metal screw or bolt near the fuse box (part of the vehicle's chassis).

    • Loosen the screw or bolt, slip the U-shaped terminal (fork connector) of the ground wire behind it, and then re-tighten the screw or bolt securely.


Step 2: Camera Positioning and Mounting

This step ensures the camera is placed correctly for optimal viewing and safety.

  • Prepare the Windshield:

    • Ensure the vehicle is on flat and level ground.

    • Clean the designated mounting area on the windshield thoroughly with an alcohol wipe and allow it to fully dry.

  • Determine Camera Position:

    • Temporarily hold the camera in place.

    • The camera should have a clear view of the road and, if enabled, a clear view of the driver/cabin.

    • Crucially, it must not obstruct the driver's field of view. Positioning it behind the rearview mirror is often ideal.

  • Initial Power Check:

    • Plug the power cable from the hardwire kit into the dashcam.

    • Turn the vehicle ignition ON to power the camera.

    • Enter the default PIN 3333 on the dashcam screen.

    • Select Live View to confirm the proper positioning and view for both the front and cabin cameras.

  • Finer Lens Adjustment (If Necessary):

    • Use the provided screwdriver to loosen the 3 small screws on the side of the camera unit.

    • Adjust the camera lenses for the final angle. Do not remove the screws; simply loosen them enough to make the adjustment.

    • Re-tighten the screws to lock the lens position.

  • Final Mounting:

    • Once satisfied with the view, remove the adhesive tape from the mounting bracket.

    • Firmly press the mounting bracket onto the windshield and hold for 30 seconds to ensure a secure bond.


Step 3: Calibration and Cable Management

This final step completes the setup and tidies the installation.

  • Perform Calibration:

    • Ensure the vehicle ignition is ON.

    • Check that the camera is on and enter the default PIN code (3333).

    • Go to Settings and select Calibration.

    • Allow the camera to complete the process. The calibration status should change from Not Completed to Completed.

  • Route the Power Cable:

    • Carefully tuck the power cable behind the headliner (the fabric ceiling) and down the side pillar trim to put it out of the way and create a clean installation.


Common installation errors come from the following:

  • Too much Sky: The road-facing camera should be adjusted to capture more road than sky. If seeing too much sky, loosen the screws and adjust the camera angle.

  • Not Enough Driver: If the cabin-facing camera is enabled, be sure to adjust downward so that the head and torso of the driver are captured.

  • Recalibration: If any adjustment is made to the camera at all (e.g., windshield replacement), the camera will need to be recalibrated.


After the camera has been properly installed and calibrated, you are ready to assign it to a vehicle on the Navistream Web Portal. For this, please visit this Support Article: Navistream Camera Management

Remember: the Camera MUST be re-calibrated when any physical adjustments are made.

If you have any questions regarding the installation, setup, or calibration of the Surfsight AI-12 camera, please contact Navistream Support.


Navistream Support

1(844)571-8200 Ext 2

navistream@stti.ca